- 96
- 2 019 770
ForkliftGeek
Canada
Приєднався 13 кві 2014
- Forklift Technician for 11 years
- Technical Trainer
- I make Forklift Diagnostic videos
- My logo was made by @logo_maximat
- Check out my instagram page @forkliftgeek
- Technical Trainer
- I make Forklift Diagnostic videos
- My logo was made by @logo_maximat
- Check out my instagram page @forkliftgeek
Raymond Reach, very slow drive No codes
A Raymond Reach truck that drives excessively slow without any error codes.
Переглядів: 3 407
Відео
Toyota 4Y cranks but doesn't start
Переглядів 6 тис.3 місяці тому
a Toyota 7 series with a 4Y engine came into the shop for a cranking no start. a tune-up was done by road service but did not fix the issue. I've done several no start diagnostics, but I've never seen this cause before.
What can cause an E-35 Code (k21 engine)
Переглядів 2,6 тис.4 місяці тому
links to the tools used in this video Piercing Probe a.aliexpress.com/_mMRfMqe Needle Probes a.aliexpress.com/_msisoMa A question was asked about what signals are preset in the LPG injector driver module. This video tries to answer that question and what can trigger an E-35 code
Nissan TB45 Engine severe low power
Переглядів 4,4 тис.6 місяців тому
Nissan forklift with a TB456 cylinder inline engine. Complain from the customer is severe loss of power.
Komatsu Forklift No power Under Load
Переглядів 3,7 тис.7 місяців тому
Komatsu forklift with a K21 engine. Customer complaint is no power under load or higher rpm.
Mitsubishi Forklift No Throttle Response
Переглядів 7 тис.9 місяців тому
Mitsubishi Forklift No Throttle Response
Toyota Forklift No drive, Blown SFT fuse
Переглядів 7 тис.9 місяців тому
Toyota Forklift No drive, Blown SFT fuse
Nissan K21engine Intermittent Stalling and No Starts
Переглядів 5 тис.Рік тому
Nissan K21engine Intermittent Stalling and No Starts
Battery Charging and testing with the TB6000Pro
Переглядів 2,1 тис.Рік тому
Battery Charging and testing with the TB6000Pro
Crown Reach No Lift, No Drive (Code 222)
Переглядів 9 тис.Рік тому
Crown Reach No Lift, No Drive (Code 222)
Yale forklift with GM 2.4 Cranking no Start
Переглядів 7 тис.Рік тому
Yale forklift with GM 2.4 Cranking no Start
Checking Ignition system with basic tools
Переглядів 24 тис.2 роки тому
Checking Ignition system with basic tools
No Crank, No Start, New Battery, New Starter
Переглядів 51 тис.2 роки тому
No Crank, No Start, New Battery, New Starter
How to test for a shorted Transistor (fault code C0)
Переглядів 7 тис.2 роки тому
How to test for a shorted Transistor (fault code C0)
Error Code 4B no power steering operation
Переглядів 4,1 тис.2 роки тому
Error Code 4B no power steering operation
Hyundai Theta, running rough, hesitates under load
Переглядів 11 тис.2 роки тому
Hyundai Theta, running rough, hesitates under load
Do not trust your compression gauge!
Переглядів 9 тис.3 роки тому
Do not trust your compression gauge!
If anyone still has the error code after trying this, i figured out what the issue is. There are 2 bushings on the bar that get worn out and prevents it from making contact to the switches when turning.
Anyone have toy diesel code 12-4, how often harness issue or always turbo????? Why are these forklifts such crap now. Toyota ran forever in the 7 series days
My 07 Silverado , new battery , new starter , put the key and nothing
Also it’s a 5.3 ls
Checked all of the fuses but nothing
Bro are you a Filipino?
Yes
Wow I'm a forklift technician here in the Philippines I work in handling innovation known as Toyota forklift most of my workmate are now working in different countries mostly in Canada and Australia I'm so proud of you Bro you so very skillful I hope someday I will become like you
Thanks for the time of answering my question God Bless
This guy sounds like a dick
Is it possible to bypass the solenoid valve for testing? mines not starting unless i spray the intake - its not clicking when i apply 12v but there is current cos it sparks lightly on jumper wire.. or can u bench test the solenoids?
Great find a lot of head scratching 👍
Having issues with my Ford F-250 did an engine swap from a V10 to a 5.4 no I have a backfire I think it's because there's two extra injectors on the V10 and the 5.4 has eight what can I do in my situation I need my truck running if you've been in this situation can you please help we're trying to troubleshoot this problem
Good catch. I wonder if the phase of the sensor signal changes as you rotate the sensor. I like this style sensor. So much easier to replace than a sensor bearing.
Are you working on Linde a lot? 😂😂😂😂 hate those bearings 😂😂
Maestro
I would've just done the pedal dance
Sounds like a cam or crank shaft sensor. On the cat,Mitsubishi/nissian/unicarrier u have to use oem sensors.
Couldn't you just order a sensor for an end rider?
I enjoy watching ur videos ❤️thanx
How in the hell did you figure that out? Bravo 👏 Usually they'll just rebuild those so how does the case get mixed up? Unless you guys ordered a reman one and they sent you one with a close but different casing
Now that is some impressive detective work. I never would have thought that could even be a possibility.
...i dont get it, those sensors are not supposed to be directional, you should be able to duck tape it in any angle and it should work the same way, there has to be something else going on there
This style of sensor has two sensors in one (phase A and phase B). The computer is watching the sequence of each phase for direction and frequency of each phase for speed. Being that the sensor was 180 deg out, the computer is seeing opposite direction than it’s expecting. If it were a single signal sensor, you’re correct the angle wouldn’t matter.
Wow thats crazy. Good job comparing to a known good truck.
Thanks 👍
I need your help boss. Are you Pinoy? I got a Toyota electric forklift that's completed dead. No ignition, battery has voltage
Why didn’t you just service the vaporiser instead of replacing it ?
Once long time ago I was noticed that only on rainy day (when there is a lot of moisture in the air) my fiat old school engine start working on 3 cylinders, than I replaced old original wires with new bosch silicone wires and than it was again nice 4 cylinder engine
😊
Hi is manny here from Raymond in Pa Where did you get the extra long socket
www.amazon.ca/dp/B0CDCN2H9H?linkCode=ssc&tag=onamzjaymatia-20&creativeASIN=B0CDCN2H9H&asc_item-id=amzn1.ideas.3AMHXHQGNZ8OE&ref_=aip_sf_list_spv_ons_mixed_d_asin&th=1
bad grown
Tengo un problema igual
What is the problem suddenly the drive motor in left side going opposite direction?
I've been work at a Toyota lift dealer for over 2 years now and I've learned more of these videos. Thank you for sharing your knowledge 👍🏾
What test light is that?
Lisle 32900
Hello colleague, excellent video and explanation of the follow-up of the failure. question, can you share the technical information of that equipment, the electrical system diagram, best regards, Milton Apraez
Y wue fue lo wue cambiaste en esta falla ke presentas
Where can I do a course on a reach truck
This amazing work proportion valve
That was good knowledge
Prob need to tighten that holder clip up & find the fuse box cover, rather than leave it loose like that!
yeah so i got a fg25n that has a little throttle response.. like you floor it, it raises rpms very slighty. like 15-20%, got e-24 and e-31 code. should i try what you did here, or is there another route i should be taking ?
Hi Forkliftgeek I have a Yale GDP25TE with a power problem,starts fine and revs no problem but sometimes when I put it in forward or reverse no drive or low power drive leave it idling for 5-10 minutes then I have full power any ideas? I did have the torque converter reconditioned last year as didn’t have power to drive over a stone! After that it was great but now 1 yr on this.I have changed fuel filter,in-line fuel filter,ATF fluid & filer still the same
Sounds like a loss of pressure from the charge pump to me.
Thanks for that @forkliftgeek10 ,what does the charge pump do? And where is it and how do I test it?
@@airwalker5404 charge pump or transmission pump creates transmission oil flow. You need a transmission pressure guage. This is only one possibility though.
@@forkliftgeek10 thanks for that,I’ll look into it, I also wondered if it was anything to do with the drive solenoid?
If you are referring to the forward or reverse solenoids, then I would say unlikely to be the cause. You said if you leave it idling for 5 to 10 mins it would drive.
Nice logical approach
Hello i am a RAYMOND tech Question, where do get your meter accessories for your multimeter
www.amazon.ca/shop/forkliftgeek?linkCode=spc&tag=onamzjaymatia-20
This link should bring you my Amazon store. You can find the tools and accessories I use in the videos. Will be adding more soon.
What solution you gave to the customer? I have the same issue with a clark
Good Please I hav error 11 in Clark c90d forklift so can you Héloïse-Luce me or if you havé thé schimatich électric thanks for you
I have something similar on an ES-B Easi reach truck three motor. The check valve on the reach manifold was also clogged with debris. Cleaned it and fixed the issue, but also noticed it does not retract while forks are on a load. You hear the aux motor running and can feel the hydraulic hoses flexing with pressure. Without a load it retracts, but does not fully nest. Could it be the reach valve that's clogged as well?
Was a bad regulator, Those ones aren't cheap
The engine has to rotate fort the solniod to pull in
i have a komatsu fg18ht-17 that intermittently will stall and/or wont start. i traced with a multi meter to figure out that at those times, the fuel solenoid isnt getting voltage. if i run 12v directly to it, it starts. I am thinking that the ecm is preventing the solenoid from energizing; possibly due to a faulty sensor (cam, crank, oil, o2)... hopefully not a faulty ecm. i have an innova 5410 as well as the komatsu adapter but unfortunately the 5410 wont read it.... says not supported. any suggestions/insight? came across your video in my hunt for info. great stuff. thanks
A faulty crank or cam would take out spark.. check the relays and and fuses.
@@forkliftgeek10 cool. thanks. I appreciate it
You keep reciting your self over and over get to the point
Great video
Language problem but I understand. You are geneus. I like Your method of understanding is very good
Hi great video.looks to me that you have connected the polarity wrong.hope you have already spoted this brother !i have made one myself and using it
weird question but what would be the equivalent of this on a 2006 f150 5,4L.Fuel pressure regulator? My truck does the same exact thing as this fork lift engine.
So i have a 6.2l im having the same issues with.. should the motor be easy to turn if its not locked.. hopefully.. because ive been thinking thats my problem with my diesel truck..